Custom Rivet — Nylon (PA) with Injection Moulding
We supply rivet to garment factories and brands, built in Nylon (PA) with injection moulding for outerwear and jacket programmes. On a trim like this the specification that decides the outcome is setting pressure, which cracks caps if it is wrong in either direction, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 500 pieces per style per finish.
The failures here are predictable: packing that arrives mixed and unusable on the line, or minimum order quantities far above what a growing brand can absorb. We lock material, finish, dimension and tolerance before bulk, and prepare SNI or SIRIM documentation per destination so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Rivet |
|---|---|
| Cap diameter | 12 mm |
| Type | double-cap rivet |
| Base material | Nylon (PA) |
| Finish / process | Injection Moulding |
| Colour options | 8 Pantone-matched shades |
| Packing | polybag per 100 |
| MOQ | 500 pieces per style per finish |
| Sampling | 14 working days, 4 days per revision |
| Bulk lead time | 20-40 days after approval |
| Compliance | SNI or SIRIM documentation per destination; CPSIA lead and phthalate testing |
| Ship to | Jakarta or Port Klang (Asia-Pacific) |
What buyers can customise
- Heat Transfer Printing — available on Nylon (PA), quoted per position and per colour.
- Paint Spray — available on Nylon (PA), quoted per position and per colour.
- Dye-Sublimation Printing — available on Nylon (PA), quoted per position and per colour.
- Black Oxide — available on Nylon (PA), quoted per position and per colour.
- Hot Foil Stamping — available on Nylon (PA), quoted per position and per colour.
- Rose Gold Plating — available on Nylon (PA), quoted per position and per colour.
- Overlocked Edge — available on Nylon (PA), quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed cap diameter
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with injection moulding applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for CPSIA lead and phthalate testing are prepared for the destination market. We ship to Jakarta or Port Klang with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same setting pressure.
FAQ
Can you do small runs across many designs?
Yes — many studio and boutique programmes run small quantities across a wide design set.
Can you match a reference sample?
Yes. Send the trim and we match material, finish and shade, then confirm on a pre-production sample before bulk.
How do you control colour on reorders?
The approved reference and the bulk standard are retained, and every reorder is checked against them before shipment.
What is the minimum order?
Programmes start at 500 pieces per style per finish. Mixed sizes are fine within one style.
Start your rivet programme
If you already have a supplier, send us the last problem you had with them. That is usually where we start.
