Custom Rib Cuff — Spandex Blend with Injection Moulding
We supply rib cuff to garment factories and brands, built in Spandex Blend with injection moulding for uniform and corporate programmes. On a trim like this the specification that decides the outcome is recovery after stretch, because a cuff that bags stays bagged, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 500 pieces per style per finish.
The failures here are predictable: unclear responsibility when a defect shows up after washing, or packing that arrives mixed and unusable on the line. We lock material, finish, dimension and tolerance before bulk, and prepare CPSIA and California Prop 65 compliance so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Rib Cuff |
|---|---|
| Width | 4 cm |
| Construction | 1x1 rib |
| Base material | Spandex Blend |
| Finish / process | Injection Moulding |
| Colour options | 8 Pantone-matched shades |
| Packing | reel packed |
| MOQ | 500 pieces per style per finish |
| Sampling | 14 working days, 3 days per revision |
| Bulk lead time | 20-50 days after approval |
| Compliance | CPSIA and California Prop 65 compliance; CPSIA lead and phthalate testing |
| Ship to | Los Angeles or New York (North America) |
What buyers can customise
- Crochet — available on Spandex Blend, quoted per position and per colour.
- Die-Casting — available on Spandex Blend, quoted per position and per colour.
- Injection Moulding — available on Spandex Blend, quoted per position and per colour.
- Piece Dyeing — available on Spandex Blend, quoted per position and per colour.
- Fringe Finish — available on Spandex Blend, quoted per position and per colour.
- Mercerised Finish — available on Spandex Blend, quoted per position and per colour.
- Sewn Edge — available on Spandex Blend, quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed width
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with injection moulding applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for CPSIA lead and phthalate testing are prepared for the destination market. We ship to Los Angeles or New York with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same recovery after stretch.
FAQ
Can you do small runs across many designs?
Yes — many studio and boutique programmes run small quantities across a wide design set.
Do you ship to our forwarder?
Yes. We deliver to your nominated forwarder or quote landed cost under the agreed Incoterm.
Which compliance documents do you provide?
We prepare CPSIA lead and phthalate testing and the supporting test reports for the destination market.
How long does sampling take?
A first sample takes 14 working days, and each revision about 3 days.
Start your rib cuff programme
Send us a reference sample, a drawing or a spec sheet and we will come back with material options, a costing and a sampling timetable.
