Custom Eyelet — Nickel-Free Alloy with Paint Spray
We supply eyelet to garment factories and brands, built in Nickel-Free Alloy with paint spray for outerwear and jacket programmes. On a trim like this the specification that decides the outcome is setting tooling tolerance, which decides whether the line runs clean, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 500 pieces per style per finish.
The failures here are predictable: unclear responsibility when a defect shows up after washing, or inconsistent sizing between production runs. We lock material, finish, dimension and tolerance before bulk, and prepare CPSIA and California Prop 65 compliance so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Eyelet |
|---|---|
| Inner diameter | 8 mm |
| Type | two-part eyelet and washer |
| Base material | Nickel-Free Alloy |
| Finish / process | Paint Spray |
| Colour options | 16 Pantone-matched shades |
| Packing | reel packed |
| MOQ | 500 pieces per style per finish |
| Sampling | 14 working days, 3 days per revision |
| Bulk lead time | 15-30 days after approval |
| Compliance | CPSIA and California Prop 65 compliance; CPSIA lead and phthalate testing |
| Ship to | Los Angeles or New York (North America) |
What buyers can customise
- Rubber Coating — available on Nickel-Free Alloy, quoted per position and per colour.
- Hard Enamel Fill — available on Nickel-Free Alloy, quoted per position and per colour.
- Injection Moulding — available on Nickel-Free Alloy, quoted per position and per colour.
- Rose Gold Plating — available on Nickel-Free Alloy, quoted per position and per colour.
- Nickel Plating — available on Nickel-Free Alloy, quoted per position and per colour.
- Stamping — available on Nickel-Free Alloy, quoted per position and per colour.
- Epoxy Dome — available on Nickel-Free Alloy, quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed inner diameter
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with paint spray applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for CPSIA lead and phthalate testing are prepared for the destination market. We ship to Los Angeles or New York with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same setting tooling tolerance.
FAQ
How do you control colour on reorders?
The approved reference and the bulk standard are retained, and every reorder is checked against them before shipment.
What is the minimum order?
Programmes start at 500 pieces per style per finish. Mixed sizes are fine within one style.
Can you do small runs across many designs?
Yes — many studio and boutique programmes run small quantities across a wide design set.
How long does sampling take?
A first sample takes 14 working days, and each revision about 3 days.
Start your eyelet programme
Send us a reference sample, a drawing or a spec sheet and we will come back with material options, a costing and a sampling timetable.
