Custom Eyelet — Polypropylene (PP) with Brushed Finish
We supply eyelet to garment factories and brands, built in Polypropylene (PP) with brushed finish for outerwear and jacket programmes. On a trim like this the specification that decides the outcome is plating that survives washing and contact with skin, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 5000 pieces per style per finish.
The failures here are predictable: unclear responsibility when a defect shows up after washing, or shade variation within one carton. We lock material, finish, dimension and tolerance before bulk, and prepare GB 18401 safety classification with GB/T 29862 fibre labelling so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Eyelet |
|---|---|
| Inner diameter | 3 mm |
| Type | two-part eyelet and washer |
| Base material | Polypropylene (PP) |
| Finish / process | Brushed Finish |
| Colour options | 16 Pantone-matched shades |
| Packing | boxed sets |
| MOQ | 5000 pieces per style per finish |
| Sampling | 14 working days, 5 days per revision |
| Bulk lead time | 15-30 days after approval |
| Compliance | GB 18401 safety classification with GB/T 29862 fibre labelling; EN 71 part 3 for decorative components |
| Ship to | Shanghai or Shenzhen (Mainland China) |
What buyers can customise
- Antique Silver — available on Polypropylene (PP), quoted per position and per colour.
- Antique Brass Plating — available on Polypropylene (PP), quoted per position and per colour.
- Rubber Coating — available on Polypropylene (PP), quoted per position and per colour.
- Overlocked Edge — available on Polypropylene (PP), quoted per position and per colour.
- Mirror Polish — available on Polypropylene (PP), quoted per position and per colour.
- Powder Coating — available on Polypropylene (PP), quoted per position and per colour.
- Nickel Plating — available on Polypropylene (PP), quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed inner diameter
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with brushed finish applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for EN 71 part 3 for decorative components are prepared for the destination market. We ship to Shanghai or Shenzhen with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same plating that survives washing and contact with skin.
FAQ
Can you match a reference sample?
Yes. Send the trim and we match material, finish and shade, then confirm on a pre-production sample before bulk.
How long does sampling take?
A first sample takes 14 working days, and each revision about 5 days.
Do you ship to our forwarder?
Yes. We deliver to your nominated forwarder or quote landed cost under the agreed Incoterm.
How do you control colour on reorders?
The approved reference and the bulk standard are retained, and every reorder is checked against them before shipment.
Start your eyelet programme
If you already have a supplier, send us the last problem you had with them. That is usually where we start.
