Custom Eyelet — Stainless Steel with Rose Gold Plating
We supply eyelet to garment factories and brands, built in Stainless Steel with rose gold plating for uniform and corporate programmes. On a trim like this the specification that decides the outcome is plating that survives washing and contact with skin, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 1000 pieces per style per finish.
The failures here are predictable: colour drift between the approved sample and the bulk trim, or shade variation within one carton. We lock material, finish, dimension and tolerance before bulk, and prepare GSO conformity with Arabic labelling so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Eyelet |
|---|---|
| Inner diameter | 4 mm |
| Type | toothed washer eyelet |
| Base material | Stainless Steel |
| Finish / process | Rose Gold Plating |
| Colour options | 24 Pantone-matched shades |
| Packing | bulk packed |
| MOQ | 1000 pieces per style per finish |
| Sampling | 7 working days, 3 days per revision |
| Bulk lead time | 25-40 days after approval |
| Compliance | GSO conformity with Arabic labelling; EN 71 part 3 for decorative components |
| Ship to | Jebel Ali (the Middle East) |
What buyers can customise
- Rubber Coating — available on Stainless Steel, quoted per position and per colour.
- Epoxy Dome — available on Stainless Steel, quoted per position and per colour.
- Chrome Plating — available on Stainless Steel, quoted per position and per colour.
- Paint Spray — available on Stainless Steel, quoted per position and per colour.
- Black Oxide — available on Stainless Steel, quoted per position and per colour.
- Injection Moulding — available on Stainless Steel, quoted per position and per colour.
- Hard Enamel Fill — available on Stainless Steel, quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed inner diameter
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with rose gold plating applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for EN 71 part 3 for decorative components are prepared for the destination market. We ship to Jebel Ali with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same plating that survives washing and contact with skin.
FAQ
Which compliance documents do you provide?
We prepare EN 71 part 3 for decorative components and the supporting test reports for the destination market.
Do you ship to our forwarder?
Yes. We deliver to your nominated forwarder or quote landed cost under the agreed Incoterm.
How do you control colour on reorders?
The approved reference and the bulk standard are retained, and every reorder is checked against them before shipment.
Can you match a reference sample?
Yes. Send the trim and we match material, finish and shade, then confirm on a pre-production sample before bulk.
Start your eyelet programme
Send us a reference sample, a drawing or a spec sheet and we will come back with material options, a costing and a sampling timetable.
