Custom Eyelet — Nylon (PA) with Nickel Plating
We supply eyelet to garment factories and brands, built in Nylon (PA) with nickel plating for bridal and eveningwear studios. On a trim like this the specification that decides the outcome is washer bite, so the eyelet does not pull out of the cloth, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 500 pieces per style per finish.
The failures here are predictable: shade variation within one carton, or inconsistent sizing between production runs. We lock material, finish, dimension and tolerance before bulk, and prepare CPSIA and California Prop 65 compliance so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Eyelet |
|---|---|
| Inner diameter | 6 mm |
| Type | toothed washer eyelet |
| Base material | Nylon (PA) |
| Finish / process | Nickel Plating |
| Colour options | 16 Pantone-matched shades |
| Packing | boxed sets |
| MOQ | 500 pieces per style per finish |
| Sampling | 12 working days, 5 days per revision |
| Bulk lead time | 25-40 days after approval |
| Compliance | CPSIA and California Prop 65 compliance; OEKO-TEX Standard 100 for dyes and trims |
| Ship to | Los Angeles or New York (North America) |
What buyers can customise
- Epoxy Dome — available on Nylon (PA), quoted per position and per colour.
- Antique Brass Plating — available on Nylon (PA), quoted per position and per colour.
- Overlocked Edge — available on Nylon (PA), quoted per position and per colour.
- Anti-Rust Treatment — available on Nylon (PA), quoted per position and per colour.
- Stamping — available on Nylon (PA), quoted per position and per colour.
- Antique Silver — available on Nylon (PA), quoted per position and per colour.
- Paint Spray — available on Nylon (PA), quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed inner diameter
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with nickel plating applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for OEKO-TEX Standard 100 for dyes and trims are prepared for the destination market. We ship to Los Angeles or New York with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same washer bite.
FAQ
What packing options are available?
Bulk packed, carded, or packed to your own size and design ratio with barcodes applied.
How do you control colour on reorders?
The approved reference and the bulk standard are retained, and every reorder is checked against them before shipment.
Do you ship to our forwarder?
Yes. We deliver to your nominated forwarder or quote landed cost under the agreed Incoterm.
How long does sampling take?
A first sample takes 12 working days, and each revision about 5 days.
Start your eyelet programme
If you already have a supplier, send us the last problem you had with them. That is usually where we start.
