Custom Rivet — Polyethylene (PE) with Epoxy Dome
We supply rivet to garment factories and brands, built in Polyethylene (PE) with epoxy dome for outerwear and jacket programmes. On a trim like this the specification that decides the outcome is cap-to-post fit, so the rivet does not spin after setting, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 2000 pieces per style per finish.
The failures here are predictable: colour drift between the approved sample and the bulk trim, or packing that arrives mixed and unusable on the line. We lock material, finish, dimension and tolerance before bulk, and prepare GSO conformity with Arabic labelling so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Rivet |
|---|---|
| Cap diameter | 15 mm |
| Type | solid rivet |
| Base material | Polyethylene (PE) |
| Finish / process | Epoxy Dome |
| Colour options | 8 Pantone-matched shades |
| Packing | bulk packed |
| MOQ | 2000 pieces per style per finish |
| Sampling | 14 working days, 3 days per revision |
| Bulk lead time | 15-30 days after approval |
| Compliance | GSO conformity with Arabic labelling; EN 71 part 3 for decorative components |
| Ship to | Jebel Ali (the Middle East) |
What buyers can customise
- Die-Casting — available on Polyethylene (PE), quoted per position and per colour.
- UV Printing — available on Polyethylene (PE), quoted per position and per colour.
- Epoxy Dome — available on Polyethylene (PE), quoted per position and per colour.
- Dye-Sublimation Printing — available on Polyethylene (PE), quoted per position and per colour.
- Debossing — available on Polyethylene (PE), quoted per position and per colour.
- Gold Plating — available on Polyethylene (PE), quoted per position and per colour.
- Sewn Edge — available on Polyethylene (PE), quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed cap diameter
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with epoxy dome applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for EN 71 part 3 for decorative components are prepared for the destination market. We ship to Jebel Ali with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same cap-to-post fit.
FAQ
How long does sampling take?
A first sample takes 14 working days, and each revision about 3 days.
Can you do small runs across many designs?
Yes — many studio and boutique programmes run small quantities across a wide design set.
Can you match a reference sample?
Yes. Send the trim and we match material, finish and shade, then confirm on a pre-production sample before bulk.
What is the minimum order?
Programmes start at 2000 pieces per style per finish. Mixed sizes are fine within one style.
Start your rivet programme
Send us a reference sample, a drawing or a spec sheet and we will come back with material options, a costing and a sampling timetable.
