Custom Rivet — Polypropylene (PP) with Soft Enamel Fill
We supply rivet to garment factories and brands, built in Polypropylene (PP) with soft enamel fill for bridal and eveningwear studios. On a trim like this the specification that decides the outcome is cap-to-post fit, so the rivet does not spin after setting, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 3000 pieces per style per finish.
The failures here are predictable: packing that arrives mixed and unusable on the line, or inconsistent sizing between production runs. We lock material, finish, dimension and tolerance before bulk, and prepare SNI or SIRIM documentation per destination so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Rivet |
|---|---|
| Cap diameter | 12 mm |
| Type | tubular rivet |
| Base material | Polypropylene (PP) |
| Finish / process | Soft Enamel Fill |
| Colour options | 24 Pantone-matched shades |
| Packing | packed to your size ratio |
| MOQ | 3000 pieces per style per finish |
| Sampling | 7 working days, 5 days per revision |
| Bulk lead time | 20-50 days after approval |
| Compliance | SNI or SIRIM documentation per destination; EN 71 part 3 for decorative components |
| Ship to | Jakarta or Port Klang (Asia-Pacific) |
What buyers can customise
- Heat Transfer Printing — available on Polypropylene (PP), quoted per position and per colour.
- Epoxy Dome — available on Polypropylene (PP), quoted per position and per colour.
- Rubber Coating — available on Polypropylene (PP), quoted per position and per colour.
- Nickel Plating — available on Polypropylene (PP), quoted per position and per colour.
- Debossing — available on Polypropylene (PP), quoted per position and per colour.
- Chrome Plating — available on Polypropylene (PP), quoted per position and per colour.
- UV Printing — available on Polypropylene (PP), quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed cap diameter
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with soft enamel fill applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for EN 71 part 3 for decorative components are prepared for the destination market. We ship to Jakarta or Port Klang with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same cap-to-post fit.
FAQ
Which compliance documents do you provide?
We prepare EN 71 part 3 for decorative components and the supporting test reports for the destination market.
Do you ship to our forwarder?
Yes. We deliver to your nominated forwarder or quote landed cost under the agreed Incoterm.
What is the minimum order?
Programmes start at 3000 pieces per style per finish. Mixed sizes are fine within one style.
How long does sampling take?
A first sample takes 7 working days, and each revision about 5 days.
Start your rivet programme
If you already have a supplier, send us the last problem you had with them. That is usually where we start.
