Custom Lace Trim — Spandex Blend with Sequin Stitching
We supply lace trim to garment factories and brands, built in Spandex Blend with sequin stitching for uniform and corporate programmes. On a trim like this the specification that decides the outcome is stretch and recovery where the lace is used on a fitted panel, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 2000 pieces per style per finish.
The failures here are predictable: packing that arrives mixed and unusable on the line, or unclear responsibility when a defect shows up after washing. We lock material, finish, dimension and tolerance before bulk, and prepare REACH and GPSR documentation so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Lace Trim |
|---|---|
| Width | 30 mm |
| Type | guipure lace |
| Base material | Spandex Blend |
| Finish / process | Sequin Stitching |
| Colour options | 6 Pantone-matched shades |
| Packing | boxed sets |
| MOQ | 2000 pieces per style per finish |
| Sampling | 10 working days, 5 days per revision |
| Bulk lead time | 20-40 days after approval |
| Compliance | REACH and GPSR documentation; EN 71 part 3 for decorative components |
| Ship to | Rotterdam or Felixstowe (Europe) |
What buyers can customise
- Piece Dyeing — available on Spandex Blend, quoted per position and per colour.
- Pantone Colour Matching — available on Spandex Blend, quoted per position and per colour.
- Heat-Cut Edge — available on Spandex Blend, quoted per position and per colour.
- Mercerised Finish — available on Spandex Blend, quoted per position and per colour.
- Yarn Dyeing — available on Spandex Blend, quoted per position and per colour.
- Knitted Structure — available on Spandex Blend, quoted per position and per colour.
- Stamping — available on Spandex Blend, quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed width
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with sequin stitching applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for EN 71 part 3 for decorative components are prepared for the destination market. We ship to Rotterdam or Felixstowe with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same stretch and recovery where the lace is used on a fitted panel.
FAQ
How do you control colour on reorders?
The approved reference and the bulk standard are retained, and every reorder is checked against them before shipment.
What packing options are available?
Bulk packed, carded, or packed to your own size and design ratio with barcodes applied.
What is the minimum order?
Programmes start at 2000 pieces per style per finish. Mixed sizes are fine within one style.
Which compliance documents do you provide?
We prepare EN 71 part 3 for decorative components and the supporting test reports for the destination market.
Start your lace trim programme
If you already have a supplier, send us the last problem you had with them. That is usually where we start.
