Custom Zipper — Polyethylene (PE) with Antique Brass Plating
We supply zipper to garment factories and brands, built in Polyethylene (PE) with antique brass plating for denim and workwear programmes. On a trim like this the specification that decides the outcome is tape shrinkage matched to the garment fabric, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 500 pieces per style per finish.
The failures here are predictable: unclear responsibility when a defect shows up after washing, or a finish that tarnishes or rubs off after washing. We lock material, finish, dimension and tolerance before bulk, and prepare CPSIA and California Prop 65 compliance so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Zipper |
|---|---|
| Gauge | #3 |
| Type | closed-end zipper |
| Base material | Polyethylene (PE) |
| Finish / process | Antique Brass Plating |
| Colour options | 12 Pantone-matched shades |
| Packing | bulk packed |
| MOQ | 500 pieces per style per finish |
| Sampling | 12 working days, 3 days per revision |
| Bulk lead time | 20-50 days after approval |
| Compliance | CPSIA and California Prop 65 compliance; EN 71 part 3 for decorative components |
| Ship to | Los Angeles or New York (North America) |
What buyers can customise
- Hot Foil Stamping — available on Polyethylene (PE), quoted per position and per colour.
- Dye-Sublimation Printing — available on Polyethylene (PE), quoted per position and per colour.
- Braided Weave — available on Polyethylene (PE), quoted per position and per colour.
- Embossing — available on Polyethylene (PE), quoted per position and per colour.
- Black Oxide — available on Polyethylene (PE), quoted per position and per colour.
- Rose Gold Plating — available on Polyethylene (PE), quoted per position and per colour.
- Digital Printing — available on Polyethylene (PE), quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed gauge
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with antique brass plating applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for EN 71 part 3 for decorative components are prepared for the destination market. We ship to Los Angeles or New York with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same tape shrinkage matched to the garment fabric.
FAQ
How long does sampling take?
A first sample takes 12 working days, and each revision about 3 days.
Do you ship to our forwarder?
Yes. We deliver to your nominated forwarder or quote landed cost under the agreed Incoterm.
Can you do small runs across many designs?
Yes — many studio and boutique programmes run small quantities across a wide design set.
Which compliance documents do you provide?
We prepare EN 71 part 3 for decorative components and the supporting test reports for the destination market.
Start your zipper programme
Send us a reference sample, a drawing or a spec sheet and we will come back with material options, a costing and a sampling timetable.
